Search

Highly effective cleaning fluid. Removes troublesome deposits from inside the engine. Dissolves sludge and lacquer formers. All types of oil-soluble and oil-insoluble residues are brought into suspension and removed during the next oil change. This allows the clean engine and fresh oil to realize their full potential. simple to use highly economical tested for the use with catalytic converters long engine service life does not attack common sealing materials restores the engine to its original performance cleaning and care Application 80 ml (1 can) is sufficient for 0.8 – 2 l of oil. Add to warm motor oil before oil change. Then allow the engine to idle for approx. 10 minutes. With manual transmissions, press the clutch lever several times, holding it for a few seconds each time. Then change the oil and the filter.

Specially developed cleaner with selected solvent combinations for fast, easy cleaning and degreasing structural parts in the two-wheel sector. For cleaning chains with and without O/X rings on two-wheelers and quads as well as drum and disc brake systems, their brake pads and components as well as brake calipers. Application Place a box or rag under the parts to be cleaned. Spray dirty chains with Motorbike Chain and Brake Cleaner and let it run off. After the solvents have evaporated (approx. 10 min), the chain will be clean and free of grease. absolutely free of chlorine removes oil and grease-based contaminants low surface tension leaves no residues high proportion of active components controlled evaporation free of residues dissolves resin and tar-type residues optimum penetration capacity optimizes economical use

Fully synthetic, extremely adherent and waterproof chain lubricating grease. With outstanding creep and lubricating effect. Particularly suitable for fast-running chains. Reduces chain elongation and helps to extend chain service life. Full effectiveness only when used unmixed. Before use we recommend cleaning the chain with Motorbike Chain Cleaner. For initial and maintenance lubrication of power-transmission chains. Especially suitable for dusty, dirty and corrosive conditions. For high-load and fast-running chains with and without O-rings and X-rings. Application Before use we recommend cleaning the chain with Motorbike Chain Cleaner. Then spray the chain with Motorbike Chain Lube. The lubricant attains its final consistency and adherence once the solvent has evaporated. excellent penetration action excellent adhesion especially cold, hot and splash-water resistant outstanding corrosion protection highest load-carrying capacity friction and wear reducing resistant to acceleration forces reduces chain elongation

White, full synthetic special grease. For optimal lubrication through visible application on the chain. Cold, heat and spray resistant. Very good adhesion and wear protection. Reduces chain elongation and extends the service life of the chain. Good creeping properties and good corrosion protection. We recommend cleaning the chain with Motorbike Chain Cleaner before use. For all highly-stressed and high-speed motorcycle chains with and without O/X-rings. Application We recommend cleaning the chain with Motorbike Chain Cleaner before use. Spray chain with Motorbike Chain Spray until white. The lubricant attains its final consistency and adherence once the solvent has evaporated. excellent penetration action excellent adhesion especially cold, hot and splash-water resistant outstanding corrosion protection highest load-carrying capacity friction and wear reducing resistant to acceleration forces reduces chain elongation

Ready-to-use mixture based on ethylene glycol. Combination of active agents with an OAT inhibitor package specially developed for modern aluminum high-performance engines. Does not contain amines, borates, nitrites, phosphates or silicates and provides outstanding protection against frost, rust and overheating. Ensures vehicle operation all year round. Used for all cooling systems and engines, particularly aluminum high-performance engines, in passenger cars, commercial vehicles, motorcycles, buses, agricultural machines as well as stationary engines and equipment that require cooling system protection of this quality. Particularly suitable for engines of the latest generation. Application Clean the cooling system with Radiator Cleaner. Then drain it, flush it thoroughly with water and fill with ready-to-use Coolant Ready Mix RAF. excellent cleaning effect excellent corrosion protection ready for use outstanding for aluminum high-performance engines provides outstanding protection against overheating prevents the cooling system from freezing up prevents operational malfunctions contains no amines, borates, nitrites, phosphates or silicates

Removes deposits on injection nozzles and in the combustion chamber. Increases the cetane number. Eliminates engine operation problems such as knocking in idle and provides round and quiet engine running. Protects the entire fuel system from corrosion. Optimizes the emission test values. Can also be used as a preventative measure. Clean engines need less fuel and reduce emissions. For all diesel engines both with and without diesel particulate filters. Preventative during every inspection, after repairs on the fuel system or to solve problems (see application description on the pack or in the technical datasheet). Turbocharger tested. Perfectly compatible with all conventional diesel and biodiesel fuels. Can contents are sufficient for up to 75 l fuel.
Application
Preventive use:　

Add to diesel fuel according to the inspection intervals.

Problem-specific use:

Disconnect fuel feed and return lines and insert into the diesel purge. Start the engine. Run the engine at a variety of different speeds and switch off before the container is empty. Reconnect fuel lines to the fuel system and check for leaks. In cases of extreme contamination, repeat the cleaning process if necessary.

eliminates diesel knocking
increases operational reliability
boosts the cetane number
guarantees optimum combustion
good corrosion protection
highly economical
reduces deposits
cleans the fuel system

High-tech ceramic wear protection. Reduces friction and wear through ceramic compounds offering high chemical and thermal resistance. Prevents direct metal-to-metal contact, thus increasing the assembly service life. Reduces fuel consumption in gasoline and diesel engines thanks to the low-friction effect. Miscible with all commercially available motor oils and motor vehicle gear oils. For engines, manual transmissions, pumps and compressors. Is added to the respective oil. Self-mixing. Sufficient for 5 liters of oil. With a long-term effect lasting around 50,000 km. Suitable for toothed belts running in oil. Not suitable for use with wet clutches!
Application
300 ml is sufficient for up to 5 liters of motor oil. Long-term effect up to 50,000 km. Shake well before use!

excellent high and low temperature behavior
chemically inert
suitable for diesel particulate filters
increases smooth operation
stable under extreme pressures
compatible with fine filters
highest thermal stability
no deposits
long engine service life
miscible with all commercially available motor oils
reduces fuel consumption
reduces frictional losses
tested for turbochargers and catalytic converters