Find Parts -     Make:     Model:          




Price filter



Sort By:
LIQUI MOLY Motorbike MoS2 Shooter 20ml (3444)
Reduces friction and wear, thus reducing oil and fuel consumption. Increases engine's running smoothness and leads to fewer malfunctions. increases smooth operation tested for the use with catalytic converters smooth engine running miscible with all commercially available motor oils miscible with all commercially available gear oils reduces oil and fuel consumption reduces wear prevents operational malfunctions minimizes friction Application In 4-stroke engines at every oil change; in 2-stroke engines add when filling the oil or fuel tank. Shake well before use! Dosage: In 4-stroke engines or the transmission: 20 ml (1 tube) is sufficient for 1 l of motor oil. For 2-stroke engines (mixture lubrication): 10 ml per 10 l of fuel mixture or for separate lubrication 20 ml for 1 l of 2-stroke oil.
LIQUI MOLY Motorbike Engine Flush Shooter 80ml (20597)
Highly effective cleaning fluid. Removes troublesome deposits from inside the engine. Dissolves sludge and lacquer formers. All types of oil-soluble and oil-insoluble residues are brought into suspension and removed during the next oil change. This allows the clean engine and fresh oil to realize their full potential. simple to use highly economical tested for the use with catalytic converters long engine service life does not attack common sealing materials restores the engine to its original performance cleaning and care Application 80 ml (1 can) is sufficient for 0.8 – 2 l of oil. Add to warm motor oil before oil change. Then allow the engine to idle for approx. 10 minutes. With manual transmissions, press the clutch lever several times, holding it for a few seconds each time. Then change the oil and the filter.
LIQUI MOLY Motorbike 4T Shooter 80ml (7822)
Optimizes engine performance. Removes deposits in the fuel system, on valves, spark plugs and in the combustion chamber and prevents renewed formation. This also reduces fuel consumption. Protects the entire fuel system from corrosion. Prevents carburetor icing. Cat tested. reduces residue increases operational reliability for carburetor and fuel-injection engines good corrosion protection highly economical tested for the use with catalytic converters optimizes engine performance environmentally friendly normalizes gasoline consumption and exhaust emissions Application Add to the fuel tank. For the optimum effect, add every time you refuel. Fully compatible with all gasoline grades. 80 ml is sufficient for 5 to 10 liters of fuel.
LIQUI MOLY Motorbike Speed Shooter 80ml (7820)
State-of-the-art, ash-free combination of agents with acceleration-enhancing, cleaning, dispersing and material-protecting properties. The product has been formulated using state-of-the-art additive and fuel technologies in accordance with the requirements of today's engines, fuels and running conditions. Ensures increased driving enjoyment due to optimized performance. The engine starts easier and also runs smoother. For 2-stroke and 4-stroke gasoline engines (aspirated and injection). 80 ml is sufficient for up to 10 liters of fuel. Recommended for use at each refueling. Application Add to the fuel tank. For the optimum effect, add every time you refuel. Fully compatible with all gasoline grades. 80 ml is sufficient for up to 10 liters of fuel. removes deposits from entire fuel system guarantees optimum combustion good corrosion protection highly economical residue-free combustion improves acceleration prevents carburetor icing higher performance gain
AMSOIL Motorcycle Octane Boost 118ml (MOBCN)
Increases octane up to three numbers for maximum power and efficiency. Designed to improve startup performance and eliminate engine ping or knock for increased power during low-rpm operation. Contains detergents that help combustion chambers and fuel-delivery systems maintain cleanliness for optimum performance. At recommended treat rate, does not harm catalytic converters or oxygen sensors.
Red Line WaterWetter Coolant Additive 12oz
Unique agent for cooling systems that doubles the wetting ability of water Rust and corrosion protection allows for use of straight water in racing or reduced antifreeze levels in warm climates Improves heat transfer and reduces cylinder head temperature Use one bottle for most passenger cars and light trucks, treats 3 to 5 gallons or 13.2 to 15.9 liters, vehicles with larger cooling systems should use two bottles, small cooling systems should use 1oz (3 to 4 capfuls) per quart Compatible with new or used antifreeze (including DEX-COOL® and long-life versions) to improve the heat transfer of ethylene and propylene glycol systems Satisfies ASTM D2570 and ASTM D1384 corrosion tests for glycol-based antifreezes Contains no ethylene glycol
AMSOIL P.i. Performance Improver 355ml (APICN)
AMSOIL P.i. is the most potent gasoline additive available today. As a concentrated detergent, it is unsurpassed in cleaning combustion chamber deposits, intake valve deposits and port fuel injector deposits. AMSOIL P.i. helps maintain peak engine efficiency, fuel economy, power and drivability in newer low mileage engines. In engines with accumulated deposits, testing showed AMSOIL P.i. provided the following clean-up benefits after only one tank of gasoline: * Improves fuel mileage an average of 2.3% and up to 5.7% * Reduces emissions --hydrocarbons (HC) up to 15% --carbon monoxide (CO) up to 26% --nitrous oxides (NOx) up to 17% * Restores power and performance * Reduces the need for costly higher octane fuel * Reduces noise from carbon rap and pre-ignition Recommendations: Treat one full tank of gas up to 20 gallons with one bottle of P.i. For very large gas tanks, partially fill to 40 gallons and treat with two bottles of P.i. Using more than two bottles per treatment is not recommended. Treat gas every 4,000 miles of service (or 100 hours for marine, stationary and off-road gasoline-powered engines). P.i. helps pass emission tests by running one tank of treated fuel through the engine prior to testing. Safe for use with catalytic converters, oxygen sensors, oxygenated gas and 10 percent ethanol blended gas. Not recommended for two-cycle engines.
AMSOIL Dominator Octane Boost 355ml (AOBBE)
• Increases octane up to 4 numbers for improved performance • Maximizes power • Reduces engine knock • Improves ignition & responsiveness • Helps fuel burn more cleanly • Removes carbon deposits For off-road and racing use only. Increases octane up to four numbers. Helps reduce engine knock for maximum power, responsiveness and performance. INCREASES OCTANE UP TO 4 NUMBERS Significantly increases engine response and power in two- and four-stroke gasoline-fueled engines. Just one treatment reduces engine knock, improves ignition and helps fuel burn cleaner. Most users find one 12-ounce (354 mL) bottle for 15 gallons (57 litres) of gasoline provides the ideal performance increase. EXCELLENT LEAD SUBSTITUTE Excellent as a lead substitute in collector automobiles, older off-road equipment and pleasure vehicles.
LIQUI MOLY Diesel Purge 500ml (1811)

Removes deposits on injection nozzles and in the combustion chamber. Increases the cetane number. Eliminates engine operation problems such as knocking in idle and provides round and quiet engine running. Protects the entire fuel system from corrosion. Optimizes the emission test values. Can also be used as a preventative measure. Clean engines need less fuel and reduce emissions. For all diesel engines both with and without diesel particulate filters. Preventative during every inspection, after repairs on the fuel system or to solve problems (see application description on the pack or in the technical datasheet). Turbocharger tested. Perfectly compatible with all conventional diesel and biodiesel fuels. Can contents are sufficient for up to 75 l fuel.
Preventive use: 

Add to diesel fuel according to the inspection intervals.

Problem-specific use:

Disconnect fuel feed and return lines and insert into the diesel purge. Start the engine. Run the engine at a variety of different speeds and switch off before the container is empty. Reconnect fuel lines to the fuel system and check for leaks. In cases of extreme contamination, repeat the cleaning process if necessary.

eliminates diesel knocking
increases operational reliability
boosts the cetane number
guarantees optimum combustion
good corrosion protection
highly economical
reduces deposits
cleans the fuel system

LIQUI MOLY Cera Tec 300ml (3721)

High-tech ceramic wear protection. Reduces friction and wear through ceramic compounds offering high chemical and thermal resistance. Prevents direct metal-to-metal contact, thus increasing the assembly service life. Reduces fuel consumption in gasoline and diesel engines thanks to the low-friction effect. Miscible with all commercially available motor oils and motor vehicle gear oils. For engines, manual transmissions, pumps and compressors. Is added to the respective oil. Self-mixing. Sufficient for 5 liters of oil. With a long-term effect lasting around 50,000 km. Suitable for toothed belts running in oil. Not suitable for use with wet clutches!
300 ml is sufficient for up to 5 liters of motor oil. Long-term effect up to 50,000 km. Shake well before use!

excellent high and low temperature behavior
chemically inert
suitable for diesel particulate filters
increases smooth operation
stable under extreme pressures
compatible with fine filters
highest thermal stability
no deposits
long engine service life
miscible with all commercially available motor oils
reduces fuel consumption
reduces frictional losses
tested for turbochargers and catalytic converters

Per Page      1 - 10 of 10
  • 1